Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Canoga Park Owner’s Guide

We stock and install Ghost Controls-compatible keypads and intercom modules throughout Canoga Park, with most keypad swaps running $145-$260 installed and intercom module replacements typically landing between $185-$340 depending on the wiring condition and whether we’re adding a new power run. Most Canoga Park calls are same-day or next-morning because we carry the common Ghost Controls components on the truck. The usual discovery is unglamorous: the keypad takes three presses to register, or the intercom works one day and stays silent the next, and the homeowner realizes the gate still opens fine from a remote but has quietly become a problem for anyone without one.

Call (805) 210-8672

We’re an independent service provider, not affiliated with Ghost Controls. What we do have is a decade of removing their weather-beaten keypads from Canoga Park gates and knowing which failure patterns repeat.

Which Ghost Controls Models This Applies To

Ghost Controls sells its keypads and intercoms across the AXXP, AXP1, and VXP series, and the part numbers matter more than the marketing names. The most common keypad we replace in Canoga Park is the AXKP wired keypad, which shows up on both gate and garage systems. If you’ve got a newer setup, you may have the AXPB push-button version with a slim profile, and the intercom side is usually the AXIC audio module or an AXIL intercom lock paired to a Ghost Controls control board.

The compatibility gotcha nobody tells you: Ghost Controls changed its keypad wiring protocol between early AXDP-era boards and the current AXX series, so a used keypad from 2018 may not talk to a board replaced in 2023. We check the control board revision number (printed on a white label on the board’s edge) before we sell you a keypad, because the wrong revision means a dead keypad and a second trip. On the aftermarket question: there are solid third-party wired keypads that work with Ghost Controls boards, but we’ve seen enough intermittent failures from bargain knockoffs that we’ll only install aftermarket units we’ve tested across multiple Canoga Park temperature swings. We stock OEM Ghost Controls parts and one aftermarket line we trust.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• Keypad needs multiple presses or won’t register at all. The membrane under the buttons breaks down from Canoga Park sun exposure, and the carbon contacts stop making reliable electrical connection. You’ll notice it worsens in heat when the membrane stiffens.
• Keypad lights up but doesn’t trigger the gate. The keypad’s relay output is working enough to power the backlight, but the signal wire to the control board has either a broken connection or a failing output transistor. This is repairable on the board level we do on our bench.
• Intercom crackles, hums, or drops audio mid-call. The intercom wiring run from the house to the gate takes on moisture where conduit joints loosen in Canoga Park’s seasonal rain, and corrosion builds at the screw terminals. The module itself is often fine; the terminations are not.
• Intercom works but won’t release the gate. The intercom lock relay on the Ghost Controls control board isn’t receiving the momentary contact it needs, or the relay itself has welded contacts. We test the relay with a meter before condemning the module.
• One specific function dies: keypad works, intercom doesn’t, or vice versa. Ghost Controls runs separate low-voltage circuits for the keypad and intercom. One failing doesn’t mean the other is next; it means the failed circuit has its own discrete problem, usually a wire or a terminal block.

Before

After

Replacement Cost & What’s Included

Here’s the pricing picture for Canoga Park, laid out the way we quote it, in writing, before any work starts:

• Ghost Controls wired keypad (AXKP or AXPB): $145-$260 installed, depending on whether the mounting post is intact and whether the existing wiring tests clean.
• Ghost Controls intercom module (AXIC or AXIL): $185-$340 installed, with the range driven by whether we need to run new low-voltage wire through the gate post or can reuse the existing run.
• Control board relay repair (keypad or intercom input): $95-$180 depending on the relay’s location and whether it’s soldered or socketed.
• Cable re-termination and waterproofing (no new part needed): $65-$140 when we can save the existing keypad or intercom by cleaning up the connections and sealing them properly.

Every price covers the part, the labor, the weather-sealing, and the test cycle we run before we leave. Under Haven Standard Clause 1, you get that price in writing before we touch a tool. And if it fails within 365 days, we come back and make it right at no charge under the Done Right Promise.

DIY or Call Us?

You can safely check three things: confirm the keypad’s backlight responds at all, look for visible corrosion where the wire enters the keypad housing, and check whether the gate opens normally from a remote. Low-voltage (12-24V) keypad work is less dangerous than line-voltage work, but there’s a catch: Ghost Controls boards are sensitive to shorts, and a sloppy splice or a wire that touches the wrong terminal can take out the control board as well as the keypad. We’ve seen a $30 attempt turn into a $400 board replacement. If you’re comfortable with a multimeter and you’ve found an obvious loose wire, a simple re-termination is reasonable. If the problem is intermittent, if you see burning or melting at any terminal, or if you’re not sure which revision of the Ghost Controls board you have, call us at (805) 210-8672 and we’ll put a technician on it before the gate becomes a bigger problem.

FAQs